Re: ATI Rage Fury Pro/Xpert 2000Pro
|
To |
czdebian-l zavinac debian bod cz |
|
From |
Petr Aubrecht <aubrech zavinac labe bod felk bod cvut bod cz> |
|
Date |
Tue, 21 Jan 2003 10:02:12 +0100 |
|
Organization |
Czech Technical University |
Jiri Masik wrote:
"Petr Aubrecht" <aubrech zavinac labe bod felk bod cvut bod cz> writes:
snad nikoho neurazim svoji tuposti, ale mam zminenou kartu (Win vypisuji:
"ATI Rage Fury Pro/Xpert 2000Pro"). Zaboha nemuzu rozchodit XWin, porad to
hlasi:
(II) Primary Device is: PCI 01:00:0
(--) Assigning device section with no busID to primary device
(EE) No devices detected.
Je graficka karta skutecne na 01:00:0? Muzete poslat Vas XF86Config-4
a vypis lspci? Jakou verzi XFree86 mate?
Jirka
V priloze posilam lspci -v, puvodni konfiguraci a nyni fungujici!
Tu fungujici jsem ziskal tak, ze jsem po zkopirovani ovladacu z
funkcniho RedHata zkopiroval taky konfigurak!!!
Z konfigurace (XF...Debian) je jasne videt, ze jsem zkusil vsechno:-)
Vysledkem bylo,ze driver tvrdil, ze kartu s timto cipem nezna, to kdyz
jsem mu vnutil i chipId. Kupodivu ten z RedHata naskocil, ani nemrkl,
aniz bych dal sahal na drivery. Ocekavam, ze rozdil bude v nahravanych
modulech, ale nevim, jaky.
Vypis lspci nasleduje:
00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and
Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corp.: Unknown device 1131 (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82820 820 (Camino 2) Chipset PCI (rev 02)
00:1f.0 ISA bridge: Intel Corp. 82820 820 (Camino 2) Chipset ISA Bridge
(ICH2) (rev 02)
00:1f.1 IDE interface: Intel Corp. 82820 820 (Camino 2) Chipset IDE U100
(rev 02)
00:1f.2 USB Controller: Intel Corp. 82820 820 (Camino 2) Chipset USB
(Hub A) (rev 02)
00:1f.3 SMBus: Intel Corp. 82820 820 (Camino 2) Chipset SMBus (rev 02)
00:1f.4 USB Controller: Intel Corp. 82820 820 (Camino 2) Chipset USB
(Hub B) (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 Pro TF
02:0b.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink]
(rev 74)
Diky za radu, kde je (byl) problem.
Petr
P.S. Nevite nekdo, jak zjistim, co je to za Unknown device?
00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory
Controller Hub (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 8027
Flags: bus master, fast devsel, latency 0
Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [88] #09 [f104]
Capabilities: [a0] AGP version 2.0
00:01.0 PCI bridge: Intel Corp.: Unknown device 1131 (rev 02) (prog-if 00
[Normal decode])
Flags: bus master, 66Mhz, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f3000000-f3dfffff
Prefetchable memory behind bridge: f3f00000-f7ffffff
00:1e.0 PCI bridge: Intel Corp. 82820 820 (Camino 2) Chipset PCI (rev 02)
(prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: f2800000-f2ffffff
Prefetchable memory behind bridge: f3e00000-f3efffff
00:1f.0 ISA bridge: Intel Corp. 82820 820 (Camino 2) Chipset ISA Bridge (ICH2)
(rev 02)
Flags: bus master, medium devsel, latency 0
00:1f.1 IDE interface: Intel Corp. 82820 820 (Camino 2) Chipset IDE U100 (rev
02) (prog-if 80 [Master])
Subsystem: Asustek Computer, Inc.: Unknown device 8027
Flags: bus master, medium devsel, latency 0
I/O ports at a800 [size=16]
00:1f.2 USB Controller: Intel Corp. 82820 820 (Camino 2) Chipset USB (Hub A)
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 8027
Flags: bus master, medium devsel, latency 0, IRQ 5
I/O ports at a400 [size=32]
00:1f.3 SMBus: Intel Corp. 82820 820 (Camino 2) Chipset SMBus (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 8027
Flags: medium devsel, IRQ 10
I/O ports at e800 [size=16]
00:1f.4 USB Controller: Intel Corp. 82820 820 (Camino 2) Chipset USB (Hub B)
(rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 8027
Flags: bus master, medium devsel, latency 0, IRQ 6
I/O ports at a000 [size=32]
01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 Pro TF
(prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 0008
Flags: bus master, stepping, 66Mhz, medium devsel, latency 64, IRQ 11
Memory at f4000000 (32-bit, prefetchable) [size=64M]
I/O ports at d800 [size=256]
Memory at f3000000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at f3fe0000 [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Capabilities: [5c] Power Management version 2
02:0b.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev
74)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management
NIC
Flags: bus master, medium devsel, latency 32, IRQ 6
I/O ports at b800 [size=128]
Memory at f2800000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
### BEGIN DEBCONF SECTION
# XF86Config-4 (XFree86 server configuration file) generated by dexconf, the
# Debian X Configuration tool, using values from the debconf database.
#
# Edit this file with caution, and see the XF86Config-4 manual page.
# (Type "man XF86Config-4" at the shell prompt.)
#
# If you want your changes to this file preserved by dexconf, only make changes
# before the "### BEGIN DEBCONF SECTION" line above, and/or after the
# "### END DEBCONF SECTION" line below.
#
# To change things within the debconf section, run the command:
# dpkg-reconfigure xserver-xfree86
# as root. Also see "How do I add custom sections to a dexconf-generated
# XF86Config or XF86Config-4 file?" in /usr/share/doc/xfree86-common/FAQ.gz.
Section "Files"
FontPath "unix/:7100" # local font server
# if the local font server has problems, we can fall back on these
FontPath "/usr/lib/X11/fonts/misc"
FontPath "/usr/lib/X11/fonts/cyrillic"
FontPath "/usr/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/lib/X11/fonts/Type1"
FontPath "/usr/lib/X11/fonts/Speedo"
FontPath "/usr/lib/X11/fonts/100dpi"
FontPath "/usr/lib/X11/fonts/75dpi"
EndSection
Section "Module"
Load "GLcore"
Load "bitmap"
Load "dbe"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "pex5"
Load "record"
Load "speedo"
Load "type1"
Load "vbe"
Load "xie"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc102"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/psaux"
Option "Protocol" "ImPS/2"
Option "Emulate3Buttons" "true"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
Identifier "Generic Mouse"
Driver "mouse"
Option "SendCoreEvents" "true"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "Emulate3Buttons" "true"
Option "ZAxisMapping" "4 5"
EndSection
#Section "Device"
# Identifier "Generic Video Card"
# Driver "vga"
#EndSection
#Section "Device"
# Identifier "Generic Video Card"
# Driver "ati"
# Option "UseFBDev" "true"
# #Option "UseFBDev" "false"
#EndSection
Section "Device"
Identifier "Generic Video Card"
Driver "r128"
BusID "PCI:1:0:0"
Option "UseFBDev" "false"
#Option "AGPMode" "2"
ChipId 0x5446
EndSection
Section "Monitor"
Identifier "Generic Monitor"
HorizSync 30-92
VertRefresh 50-85
Option "DPMS"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "Generic Video Card"
Monitor "Generic Monitor"
DefaultDepth 8
SubSection "Display"
Depth 1
Modes "1280x1024" "1280x960" "1152x864" "1024x768"
"800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1280x1024" "1280x960" "1152x864" "1024x768"
"800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x1024" "1280x960" "1152x864" "1024x768"
"800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1280x1024" "1280x960" "1152x864" "1024x768"
"800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x1024" "1280x960" "1152x864" "1024x768"
"800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x1024" "1280x960" "1152x864" "1024x768"
"800x600" "640x480"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
#InputDevice "Generic Mouse"
EndSection
Section "DRI"
Mode 0666
EndSection
### END DEBCONF SECTION
# File generated by anaconda.
Section "ServerLayout"
Identifier "Anaconda Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.
FontPath "unix/:7100"
EndSection
Section "Module"
Load "GLcore"
Load "dbe"
Load "extmod"
Load "fbdevhw"
Load "pex5"
Load "dri"
Load "glx"
Load "pex5"
Load "record"
Load "xie"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
# Option "AutoRepeat" "500 5"
# when using XQUEUE, comment out the above line, and uncomment the
# following line
# Option "Protocol" "Xqueue"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
# Option "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:nocaps"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
#Option "XkbVariant" ""
#Option "XkbOptions" ""
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
#Option "CorePointer"
Option "Protocol" "ImPS/2"
Option "Device" "/dev/psaux"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "yes"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 30.0-96.0
VertRefresh 50.0-160.0
Option "dpms"
# -- 1400x1050 --
# 1400x1050 @ 60Hz, 65.8 kHz hsync
Modeline "1400x1050" 129 1400 1464 1656 1960
1050 1051 1054 1100 +HSync +VSync
# 1400x1050 @ 70Hz, 76.8 kHz hsync
Modeline "1400x1050" 151 1400 1464 1656 1960
1050 1051 1054 1100 +HSync +VSync
# 1400x1050 @ 75Hz, 82.3 kHz hsync
Modeline "1400x1050" 162 1400 1464 1656 1960
1050 1051 1054 1100 +HSync +VSync
# 1400x1050 @ 85Hz, 93.2 kHz hsync
Modeline "1400x1050" 184 1400 1464 1656 1960
1050 1051 1054 1100 +HSync +VSync
EndSection
Section "Device"
# no known options
Identifier "ATI Rage 128"
Driver "r128"
VendorName "ATI Rage 128"
BoardName "ATI Rage 128"
#BusID
EndSection
Section "Screen"
Identifier "Screen0"
Device "ATI Rage 128"
Monitor "Monitor0"
DefaultDepth 24
Subsection "Display"
Depth 24
Modes "1024x768"
EndSubsection
EndSection
Section "DRI"
Mode 0666
EndSection
Partial thread listing:
- Re: ATI Rage Fury Pro/Xpert 2000Pro, (pokračuje)
MeDon
prekladac gcc 2.91.66
Jiri Horak